lite-on dcc release bns-od-fc001/a4 lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL3H3ERADS2 spec no. :ds20-2017-0064effective date: 11/23/2017 revision: -
1 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 through hole lamp LTL3H3ERADS2 rev description by date p001 preliminary spec (rdr-20141583-01) craig 02/05 /2015 above data for pd and customer tracking only - customer approved and upload to opnc banjerdluk p . 06/26/2017
2 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 1. description 5mm round lamp is a popular design with a smooth un iform view angle radiation pattern suitable in full color signboard, billboard sign, message sign and bus sign. high lum inous intensity output has a higher emitting effici ency to save power energy. advanced epoxy technology has a good moistu re resistance and uv protection to be used in packa ge, and it can reduce the effect of long term exposure in outdoor environment. 1. 1. features high luminous intensity output. low power consumption & high efficiency. superior resistance to moisture. good uv inhibitor. lead free & rohs compliant. lead free reflow solder compatible. 3mm oval ,red alingap 624nm lamp, red color diffused package. wide view angle major axis 100/minor axis 45. 1.2. applications rgb full color signs billboard sign message sign bus sign 2. outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted . 3. protruded resin under flange is 1.0mm (.04") max. 4. lead spacing is measured where the leads emerge fro m the package. 5. specifications are subject to change without notice .
3 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 3. absolute maximum ratings at ta=25 parameter maximum rating unit power dissipation 75 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 120 ma dc forward current 30 ma derating linear from 40 0.51 ma/ reverse voltage 5 v operating temperature range -40c to + 85c storage temperature range -40c to + 100c lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical characteristics at ta=25 parameter symbol min. typ. max. unit test condition luminous intensity iv 1500 2500 3200 mcd if = 20ma note 1,5 viewing angle 2 1/2 100/45 deg note 2,7 (fig.6) peak emission wavelength p 631 nm measurement @peak (fig.1) dominant wavelength d 618 624 630 nm note 4 spectral line half-width ? 30 nm forward voltage vf 1.9 2.4 2.6 v if = 20ma reverse current ir 100 a vr = 5v note: 1. luminous intensity is measured with a light sens or and filter combination that approximates the cie eye-response curve. 2. 1/2 is the off-axis angle at which the luminous int ensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 5. iv guarantee must be included with 15% testing tolerance. 6. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation.
4 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 5. typical electrical / optical characteristics cur ves (25 ambient temperature unless otherwise noted)
5 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 6. packing spec. 1000, 500 or 200 pcs per packing bag 8 packing bags per inner carton total 8000 pcs per inner carton 8 inner cartons per outer carton total 64000 pcs per outer carton in every shipping lot, only the last pack will be n on-full packing
6 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 7. bin table specification luminous intensity iv (mcd) if@20ma bin code min. max. r 1500 1900 s 1900 2500 t 2500 3200 note: tolerance of each bin limit is 15% dominant wavelength unit : nm@20ma bin code min max r01 618 630 note: tolerance of each bin limit is 1nm
7 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 8. cautions 8.1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 8.2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is re commended that leds out of their original packaging are used withi n three months. for extended storage out of their o riginal packaging, it is recommended that the leds be stored in a sealed con tainer with appropriate desiccant or in desiccators with nitrogen ambient. 8.3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the leds if necessary. 8.4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do no t use the base of the lead frame as a fulcrum during forming. lead formin g must be done before soldering, at normal temperat ure. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 8.5. soldering when soldering, leave a minimum of 3mm clearance fr om the base of the lens to the soldering point. dip ping the lens into the solder must be avoided. do not apply any external s tress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions: soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2mm from the base of the epoxy bulb pre-heat pre-heat time solder wave soldering time dipping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2mm from the base of the epoxy bulb note: excessive soldering temperature and/or time m ight result in deformation of the led lens or catas trophic failure of the led. ir reflow is not suitable proce ss for through hole type led lamp product. 8.6. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connecte d in parallel in an application, it is recommended that a current limit ing resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model (a) circuit model (b) led led (a) recommended circuit (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds.
8 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 8.7. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use a conductive wrist band or anti- electrostatic glove when handling these leds all devices, equipment, and machinery must be prop erly grounded work tables, storage racks, etc. should be properl y grounded use ion blower to neutralize the static charge whi ch might have built up on surface of the leds plast ic lens as a result of friction between leds during st orage and handing suggested checking list: training and certification 8.7.1.1. everyone working in a static-safe area is esd-certified? 8.7.1.2. training records kept and re-certific ation dates monitored? static-safe workstation & work areas 8.7.2.1. static-safe workstation or work-areas have esd signs? 8.7.2.2. all surfaces and objects at all stati c-safe workstation and within 1 ft measure less tha n 100v? 8.7.2.3. all ionizer activated, positioned toward s the units? 8.7.2.4. each work surface mats grounding is g ood? personnel grounding 8.7.3.1. every person (including visitors) han dling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 8.7.3.1. if conductive footwear used, conductive flooring also present where operator stand or walk? 8.7.3.2. garments, hairs or anything closer th an 1 ft to esd items measure less than 100v*? 8.7.3.3. every wrist strap or heel strap/condu ctive shoes checked daily and result recorded for a ll dls? 8.7.3.4. all wrist strap or heel strap checker s calibration up to date? note: *50v for blue led. device handling 8.7.4.1. every esds items identified by eia-47 1 labels on item or packaging? 8.7.4.2. all esds items completely inside prop erly closed static-shielding containers when not at static-safe workstation? 8.7.4.3. no static charge generators (e.g. pla stics) inside shielding containers with esds items? 8.7.4.4. all flexible conductive and dissipati ve package materials inspected before reuse or recy cle? others 8.7.5.1. audit result reported to entity esd co ntrol coordinator? 8.7.5.2. corrective action from previous audit s completed? 8.7.5.3. are audit records complete and on file ?
9 / 9 part no. : LTL3H3ERADS2 bns-od-fc002/a4 through hole lamp LTL3H3ERADS2 9. reliability test classification test item test condition sample size reference standard endurance test operation life ta = 25c if = 30ma test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-750d:1026 (1995) mil-std-883g:1005 (2006) high temperature high humidity storage (thb) ta = 85c rh = 85% test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-202g:103b (2002) jeita ed-4701:100 103 (2001) steady state operation life of high humidity heat ta = 85c, rh= 85 % if = 15ma test time= 500hrs 76 pcs (cl=90%; ltpd=3%) jesd22-a101c (2009) low temperature operation life of ta = -30c if = 30ma test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) high temperature storage ta= 105 5c test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) mil-std-750d:1031 (1995) mil-std-883g:1008 (2006) jeita ed-4701:200 201 (2001) low temperature storage ta= -55 5c test time= 1000hrs 45 pcs (cl=90%; ltpd=5%) jeita ed-4701:200 202 (2001) environmental test temperature cycling 100c 25c -40c 25c 30mins 5mins 30mins 5mins test time: 200 cycles 76 pcs (cl=90%; ltpd=3%) mil-std-750d:1051 (1995) mil-std-883g:1010 (2006) jeita ed-4701:100 105 (2001) jesd22-a104c (2005) thermal shock 100 5c -30c 5c 15mins 15mins test time: 200 cycles 76 pcs (cl=90%; ltpd=3%) mil-std-750d:1056 (1995) mil-std-883g:1011 (2006) mil-std-202g:107g (2002) jesd22-a106b (2004) solder resistance t.sol = 260 5c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2031(1995) jeita ed-4701: 300 302 (2001) solderability t. sol = 245 5c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2026 (1995) mil-std-883g:2003 (2006) mil-std-202g:208h (2002) ipc/eia j-std-002 (2004) soldering iron t. sol = 350 5c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil-std-202g:208h (2002) jeita ed-4701:300 302 (2001) 10. others the appearance and specifications of the produ ct may be modified for improvement, without prior n otice.
|
